[tp widget="default/tpw_default.php"]

how to build a wooden fishing net插图

How to make a wooden basketball net?

The Jig is to rap the strips of Ash and Walnut to make the hoop of the net. This is not easy. Everything has to be uniform so the net is uniform. Any imperfections in the jig will result in imperfections in the hoop. No one wants a funny looking wooden net. Once you get your jig the way you want it, then you cut your strips of Ash and Walnut.

How much wood do I need to make a net?

A 1/2-inch strip of wood is cut from the second piece of particle board (Jig sheet B) in the desired shape of the net. We used a traditional teardrop shape.

What are the parts of a fishing net made of?

Our nets are made from four wood parts: three clear (knotless) hardwood strips to form the frame, and a handle insert. Our group used combinations of dark walnut and light birch strips. Other woods like maple are also suitable.

What is the best way to make a landing net?

This method uses a particle board form cut to the shape of the landing net hoop. Inner tube tire is cut into long 1 inch wide strips. The rubber strips are used to clamp the four glue covered 1/8 thick wood laminates onto the mold and handle inset.

How to tie a shuttle to a gauge?

Pass the shuttle under this loop and up to the right of the taut loop; continue pulling the shuttle and twine up until the knot formed is tight around the gauge. Then repeat this step one more time.

How to get the shuttle to come back?

Take the twine and loop it around the center peg of the shuttle so it comes back towards you.

How to make a net out of twine?

1. Load your shuttle. To begin, you’ll need to wrap your twine around the shuttle you’ll use for your net. If you run out of twine before the shuttle is full, tie the end to another spool of twine. Cut the tags that remain on the knot and continue loading.

How to pull a knot tighter?

You should be able to pull the knot tight and the gauge closer to the knot by bringing the shuttle upwards through the loop.

What is an overhand knot?

The overhand knot is the one most everybody is familiar with: you make a loop and pass the end of the line through the loop, pulling both ends to tighten.

How to make a fishing net?

1. Choose your string. In theory your fishing net can be made of any string or twine. Think about what species you’re trying to catch, and how it’s size might affect the strength of the string used. It’s recommended that you use a bonded nylon string for strength. Of all contemporary twine it is the most durable and reliable.

How to make a net stronger?

Make another knot with your shuttle. Repeating the knot is important for the eventual strength of your finished net. The more knots, the sturdier the net will be.

How are soaked wood strips formed?

To pre-form the wood strips (prior to gluing), the soaked strips are hand formed around jig section #6 (screwed to the jig base rectangle), and jig sections 1 to 5 are clamped and then screwed into placed around the veneer strips.

What is a net shaping jig made of?

A net shaping jig is made from two rectangles of strong 3/4-inch particle board. Plywood could also be used. (Details on request.)

What wood is used for nets?

Our nets are made from four wood parts: three clear (knotless) hardwood strips to form the frame, and a handle insert. Our group used combinations of dark walnut and light birch strips. Other woods like maple are also suitable. I used the walnut on the outsides of the frame and placed the lighter birch in the middle, like a rye and cheese sandwich. I also decided on the darker walnut for the handle insert. Others used the reverse combination.

How long to soak wood strips in water?

Three thin strips of wood about 6 feet long and 1/8 inch thick are cut on a table saw. The strips are soaked in hot/warm water for 3 hours in an upright 4-inch plastic PVC tube that has been capped on the bottom.

What is handle insert?

In damper climates overnight would be better. A handle insert is cut from a solid board of either the light or dark wood. The pre-formed wood strips are removed from the jig. The wood strips and handle insert are coated with carpenter’s glue on all contact surfaces.

How long does it take to make a webbing basket?

Manufactured net webbings can also be used. The whole process took something like 10 hours for each net. There are several tasks that require two or three sets of hands so it would be a good idea to work with others.