[tp widget="default/tpw_default.php"]

how to build a bamboo fishing pole插图

How to use a bamboo cane pole for fishing?

Rotate the pole so that you twist the line all the way to the tip of your bamboo cane pole. When you get to the top do a half hitch and secure the line in the slit that you made in the tip. Leave enough monofilament so that you reach near the handle of the cane pole.

How to make a bamboo fishing rod?

Find a straight piece of bamboo, about 7 feet is perfect. Trim off the leaves and rough edges. Step 2: Attach the Line. Get a piece of 10lb or stronger test line. Cut it a bit more the twice as long as your rod blank. Tie one end near the handle. Tape over the knot and down to the base to make your hand grip. Duct tape works perfectly.

How big should a bamboo pole be?

Select a good piece of bamboo, at least 10 feet long. Use the tape measure to check the size of the cane before you cut it. The butt end of the pole should be about 1 inch in diameter or slightly larger, while the tip should taper down to about one-quarter inch.

How do you cut a large bamboo pole?

Use the tape measure to check the size of the cane before you cut it. The butt end of the pole should be about 1 inch in diameter or slightly larger, while the tip should taper down to about one-quarter inch. Use the saw to cut the bamboo near ground level. Cut off all branches close to the main pole.

How to line a fly rod?

With an arbor knot, attach 20-pound Dacron line a few inches above the place where you’ll hold the rod. Lay the line along the length of the pole and whip-finish the running line to the rod with old fly line at two spots in the middle of the rod–a few feet apart–and at the tip. (If the rod tip breaks, the line will remain attached to the pole.) Attach a 2-foot monofilament leader. Total length of the line from the tip of the rod should be about 14 to 16 feet. Finish with a slip bobber, split shot, and a long-shank Aberdeen hook for easy removal.

How to make a cane pole?

1. Cut Your Cane. Cut a straight piece of cane about 10 feet long. Trim the leaf stems as close as possible. Saw through the fat end at the bottom of a joint so the butt end will have a closed cap. Smooth the rough edges with sandpaper. 2. Dry Your Cane Pole.

Is cane pole fishing a lazy pursuit?

Cane-pole fishing is hardly a lazy pursuit, with all the fish-catching that typically accompanies an outing with the bamboo and bait. And, it’s not just for pan-sized fish, either.

Can you fish with bamboo poles?

You could use one of those fancy side-scan sonar depthfinders with the new underwater fish-eye orthographic readouts. Or you could go cut a switch of bamboo and do a little cane-pole fishing. If you choose the latter, a decent cane pole is as close as the nearest stand of bamboo. Everyday ordinary, backyard bamboo works just fine for panfish, bass, and small catfish.

How does a rod jig work?

Understanding how rodmaking works means understanding how the tapering jig works . The tapering jig, also called a planing form, is made of two bars of steel five feet long. The edges that face each other are chamfered and form a V-groove when the bars are put together. At one end of the jig the chamfers form a deep valley; at the other end they form a shallow valley. In between, the chamfer forms a valley that slopes evenly between the two ends. The bamboo sits proud of the jig, and you plane it until the plane is riding on the jig. When it is, the bamboo is the same shape as the valley—wide at one end, narrow at the other. Because of the hundreds of different rod tapers, you can adjust the depth of the valley every five inches using a pair of bolts. One bolt pushes the metal bars further apart, the other pulls them together.

How to calibrate a depth gauge?

Here’s the solution. Zero out your dial caliper and then set the opening between the jaws to .100. Put the dial indicator between the jaws, and turn the dial until it reads .866. Lock the dial in place, and you’ve calibrated the depth gage. You’ll note the wooden base on my depth gauge. The 60-degree tip is a bit wide, and catches on the metal base that came with the indicator. A lot of rodmakers use wooden bases, and until I get around to buying a new tip, I will, too.

What is bamboo culm?

Technically, bamboo is a grass, and a stick is called a culm. The easiest and fastest way to get the strips you need is to split the culm the way Windsor chair makers rive a chair back from a log, and for the same reason. Splitting bamboo gives you a piece with long parallel strands of grain.

How many triangle sections of bamboo are there?

Close-up cross-section of six triangle sections of bamboo that are glued to creat the hexagon shaped rod shaft.

How many strips of bamboo are in a fly rod?

A bamboo fly rod is made of six strips of bamboo glued together to form hexagon (photo below). The strips are triangular in cross-section, and since the rod tapers from handle to tip, the triangular strips taper, too — the triangle is bigger at one end of the strip than the other.

What is split bamboo?

Splitting bamboo gives you a piece with long parallel strands of grain. Rodmakers often make their own splitters out of knives or screwdrivers that they drive into the end of the culm. Mine are chisels with edges that are ground to a rounded point.

What is the purpose of threading upholstery rods?

The purpose of all this is to wrap upholstery thread around the rod and bind the pieces together. The thread feeds from above, is tucked under the drive string at the rod, and spirals around the rod as it moves.

How to make a bamboo cane?

Step 1. Select a good piece of bamboo, at least 10 feet long. Use the tape measure to check the size of the cane before you cut it. The butt end of the pole should be about 1 inch in diameter or slightly larger, while the tip should taper down to about one-quarter inch. Use the saw to cut the bamboo near ground level.

How high should a pole be to hang?

The anchor must be at least 10 feet above the floor, so that the pole will hang freely. Use the other length of twine to tie the butt end of the pole to the hammer, which serves as a conveniently shaped weight that helps keep the pole straight.

How long does it take for a pole to dry?

Leave the pole hanging until it dries and turns brown. This may take a few days in warm, dry weather or many weeks in damp conditions. Once dry, remove both lengths of twine.

How to secure line to fish pole?

Lay the line alongside the pole. Secure the line to the pole every foot or so with the electrical tape. Wrap the line around the tip of the rod several times and secure it into place with a strip of electrical tape. By securing the line to the rod at multiple locations, you can avoid losing your fish, should the tip of the pole break.

Is bamboo cane pole good for fishing?

Lacking a reel full of line that is sure to become tangled, cane poles are great for teaching young anglers to fish. However, bamboo cane poles are not only good for youngsters; they are also useful for experienced anglers. The simplicity of cane poles makes it easy to place your bait exactly where you want it, …

Can bamboo poles be used for fishing?

How to Make a Cane Bamboo Fishing Pole. Lacking a reel full of line that is sure to become tangled, cane poles are great for teaching young anglers to fish. However, bamboo cane poles are not only good for youngsters; they are also useful for experienced anglers. The simplicity of cane poles makes it easy to place your bait exactly …

Can you catch fish with a cane pole?

The pole will not work as well, but it should still allow you to catch fish. Experiment with the length of the cane pole and the length of line. In general, longer poles allow you to reach farther from the shore, but excessively long poles are unwieldy. References. International Game Fish Association: Learn How to Make a Cane Pole.

How to make a bamboo fishing pole?

First, let’s start with the materials you’ll need to get started: Bamboo or a long flexible stick. Machete or knife to cut limbs. Dacron and/or monofilament fishing line. Bobber.

How to straighten bamboo poles?

Firing to straighten the bamboo: One of the most important steps in the process is to heat the bamboo and use a block of hardwood to slowly start to straighten the pole. Little by little the master gets the bamboo perfectly straight and with the right springiness.

How to leave monofilament on cane pole?

Leave enough monofilament so that you reach near the handle of the cane pole. Some people like to leave it a little shorter or longer, depending on preference.

How long does it take to make a Kishu Herazao?

These rods take six months to make and follow a twelve-step process:

How to find straight bamboo?

Your goal is to find the straightest bamboo you can find especially at the tip. Take your machete or knife and cut off all the branches so only the stalk remains. Remember to keep the machete flat against the stalk and cut away from you.

How to make sure your cane line doesn’t hang up?

Make sure all the notches are smooth so your line doesn’t hang up on them (always cut towards the tip of the cane pole).

What is the process of getting the tapers on the ends necessary for the pole sections to fit together?

Carving : This process gets the tapers on the ends necessary for the pole sections to fit together.